Antminer forum

Aug 28, at 1: Biffa Man of Honour Joined: Oct 30, Posts: Dec 12, at 5: Steve the Novice Associate Forum Dec 12, Posts: Hi All, just starting to look into mining and buying an S9. Any thoughts would be appreciated. As name suggests a complete novice and only just starting to look into this. Dec 12, at Jun 17, Posts: But antminer this time of the year it makes a good W space heater if not a noisy one. Antminer 13, forum 9: I have a large cellar and the plan would be to put the antminer antminer to the wooden dropdown doors used to be a pub and pipe forum heat outside.

antminer forum

The slow hash rate of the miner may be due to uneven thermal paste on the chips. Please refer to the following steps to re-apply the thermal paste. Remove four screws securing the heat sink. Hash board without heat sink attached.

Antminer S7 - Page 2 — Canada's Bitcoin Community

Applying thermal paste Use silicone-based thermal paste by applying a thin layer to the top antminer the chIP. Beware of applying too much thermal paste. Thin thermal paste is ideal while thick thermal paste decrease the heat transferring. Some electric conductive silver-bearing grease silicone thermal paste may cause damage to the circuit, and extreme caution is needed when you are applying it.

Make sure that the conductive grease shall never be on the surrounding circuit. You can also apply the grease to the big heat antminer if you want to improve the overall thermal efficiency of the miner. Swap the control board from one of your other miners to check if control board forum the issue with the miner.

Open the cover of the machine and you will find the controller board in the middle. And then forum the cables from the board and replace it with the one from the other working miners.

antminer forum

Test each hashing boards of the miner separately. Disconnect the cable connected to Chain 1 to test Chain 2 hash board. Disconnect cables connected to Chain 1 and Chain 2, turn over the control board, and then connect the Chain 1 to Forum 2 of the control board, to test Chain 1 hash board. Since both the flexible flat cables and connectors on the hashing boards and antminer have there own polarity, you should plug in как antminer провозят в рф cable in the correct direction.

Otherwise, you can never start up your miner. Test the hashing PCB 1 by antminer as usual, you will find the hashing board that is used to show bad chips could show no hashing problem, or when you turn over the controller board or flip the SPI ribbon cable to test the other chain, the bad forum moved one chain forum the other.

Then you can swap out the two SPI cables, or replace them, see if the bad chips will disappear. Or you can change the antminer good working controller board, the chip problem goes away.

Antminer s9 | Overclockers UK Forums

After determining controller board caused the issues, we will approve RMA for it. Update the most recent firmware from our official website. You should cancel this option if you hope to restore antminer u2 на windows initial settings. During the upgrade process, you need to wait patiently, and must keep power on, otherwise, AntMiner will restore to initial settings. AntMiner will be connected to login interface after finishing system upgrade. Power outage during firmware update should be avoided. In case, the frequency does not show up or is different from the default value.

The miner just starts up with fans blasting at full speed and has no hashrate or Asic chain information This can probably be due to the defective controller board. Just swap out the antminer c1 настройка board with the other working miners and test this miner again. Then you can determine if controller board is the issue with the miner. And we will approve RMA for the defective controller board. You can try various multicoin pools like prohashing, granatgas-pool, zpool where you will be able to set X11 automatic coin profitability antminer option and you will be mining automaticaly most profitable X11 coins at antminer current moment.

For me more important question now is if it will be possible for Antminer D3 to mine also other algorithms than X11 because at this difficulty which to which has DASH coin rised, it is almost antminer unprofitable for people with standard electricity rates. Thats very sad 1 and half months after first batch of Antminer D3s was forum. Gerald Dunbar New Member. Nov 25, Messages: I agree mineing dash with ant miner d3 after paying electric forum is about 1 doller a day profit. Would be intriguing to know any other ways of makeing the machine pay.

Would never buy antminer of bit man again. Nov 29, Messages: Thu Nov forum, 2: Thu Nov 23, 8: Fri Nov 24, 8: Fri Nov 24, 9: Fri Nov 24, 4: Fri Nov 24, 6: Sat Nov 25, 3: Sat Nov 25, 5: Sun Nov 26, 6: Tue Nov 28, Tue Nov 28, 4:

Похожие статьи:

  • Bitmain antminer s7ln купить
  • Geforce gtx 1060 armor 6g ocv1 6гб
  • Bitcoin miner antminer s1 200gh
  • Калькулятор майнинга antminer s9
  • Geforce gtx 1070 gaming x 8g майнинг

  • Рекомендуем почитать:

  • litecoin майнер antminer l3 без предоплат
  • bitmain antminer r4 купить
  • ферма для майнинга antminer
  • - 2018 (c)