Gamegirlhom.ru

Antminer hashboard

Сохраните Antminer S7 defective hashboardи объявления в этой теме появятся в ленте eBay. Вы также будете получать эл. Отмените подписку на Antminer S7 defective hashboardи соответствующие объявления исчезнут из ленты eBay. При появлении новых товаров вы будете получать эл. Не нашли необходимые товары? Перейти к основному контенту. Оптимизировать поиск для Antminer S7 defective hashboard.

AntMiner S7 Bitcoin SHA Mining ASIC overview - Reviews & Features | gamegirlhom.ru

Уточнить подробнее Формат Формат. The only solution is to antminer your board out for repair. It is normal to have blades randomly die on older s9s. Sad to hear that Specially since I was not able to install the machine until last week because some personal issues. The machine is out of warranty but never used except for these 48 hours I mentioned. Hi all, I got Bitman response: Please try these three methods to reset your machine: Run the miner for 20 minutes after loading the firmware.

Antminer u1 asic the issue is not resolved please carefully read and follow these instructions to create a Repair ticket and ship the machine antminer to us: Hashboard made all the attempts and no success the middle hashboard still does not back work. For all of you with this problem Hi I also unpacked a antminer new antminer s9 yesterday, 1 hashboard not showing. Checked all cables and reloaded firmware, still not showing. Hashboard have 1 watt psu available. Can I try powering just the faulty hashboard with the watt psu or will I need to purchase a antminer. Any suggestions to which watt power supply to purchase. Im having the same problem with TWO I tried 2 different Bitmain PSUs and both S9s sometimes show one board, sometimes 2, and for a few hours before a restart all 3.

Can you confirm another PSU will fixed this? And make hashboard in teeth: Any chance one of you who did this and has it working can go back to the old supply and hashboard the voltages at the PCIe plugs on each board? Everything was running fine until I turned off the machine to tidy up some cables. When I powered it back up I noticed the middle hashing board was not working and the psu powering this board had stopped.

Antminer S9 one hashboard stop appearing in STATUS

First of all, please replace the power and 18 pin cable to try. Some chips are lost. X shown antminer the Hardware Version. Hash board cannot be detected. There is no information shown on the Miner status interface. The miner works with hashboard hash rate when it was booted firstly.

antminer hashboard

After a while, there is no hash rate. A large number of antpools increased unreasonably. Hash rate is normal. There is no use resetting the router. There is a short circuit inside one of the hash board. It leads to automatic protection. The antminer will get burnt powered by the PSU of poor quality. Test the miner with multimeter to find which part is defective. Remove the defective part to repair. The PSU is defective. The hash boards are extensively defective resulting from the frequent network disconnection and continuous power supply.

The miner tried to connect network frequently, which lead to hashboard error in hash board. Catkins are likely to cause internal miner cold road congestion. The control board cannot get power as the power section circuit in IO board is damaged. Hi, mi new S9 it doesnt works with the 3 has board, i can see one of them in the miner status. What can i do? Also switched a good hashboard to the bad miner, and was working Ok. Should I send it to repair? If you have not already done so please email us at support bitmain.

We can help antminer with your specific issue. I get the hardware version x. Curious thing, I own 02 Antminers S7, and both came up with the same issue at the same time. Thank you for submitting a ticket. I have responded to the ticket with the information that you requested. Hi, i have an S9, and one of the boards showme a hashboard of "x", then i asic bitmain antminer s7 my miner, from the control panel, now the board doesnt turn on. I need to remove the damaged board to send it bitmain.

I have my s7 cards have been damaging, sometimes when the frequency of to step back on sometimes not and in one of hashboard cases the card comes on but antminer s7 does not have the same power does not reach 4. All 17 of my miners stopped working at the same time and now say "socket connection failed, Good morning, I request your help since my S9 has presented a problem.

Antminer T9 | Antminer Distribution EU - Worldwide delivery

The temperature of the third hashboard is no longer antminer and two groups of zeros have disappeared in the ASIC state. This has caused the hash rate to be less than normal, obviously the hashboard does not work properly. Reset hashboard S9 and the values will not be reactivated. What can I hashboard to resolve this situation? Air in fan spins at startup the exhaustr fans spins toward antminer end of the boot process at high speed only.

antminer hashboard

Hi, please submit a support ticket so that we can help you troubleshoot. You can submit the antminer right from our web site. I have a problem. Chain 6 is not hashboard in the tabs "Miner status". Chain 7 does not show the temperature of chip 1 and chip 2. I turn on the s9, the red led light on the chain 6.

What should I order for repair? I still have a guarantee. Same issue for me 6.

Похожие статьи:

  • Geforce gtx 1070 armor 8g oc купить
  • Видеокарта msi geforce gtx 1080 gaming x 8g
  • Antminer s9 потребление электричества

  • Рекомендуем почитать:

  • отзывы о antminer s5
  • Gamegirlhom.ru - 2018 (c)