Gamegirlhom.ru

Antminer s1 pool

Here is the video to show what the minder does, when the internet connection was disrupted. When the miner regains the internet connection, the clicking noise goes away and about 30 seconds or so later, the green LEDs will start flashing again. OR It could be powered on for about 30 seconds then it shuts down. Your problem is more than likely in the PSU.

How to Setup an Antminer S1Bitcoin Miner – domsteil

Make sure you are not using the thin loose wire or paperclip for this If the Jumper Cable is jammed in and set correctly, it could be your power supply unit. I understand that you could be using the W or even W PSU but it may not be strong enough to do the job. Questions Tags Users Badges Unanswered. Bitcoin Stack Exchange is a question and answer site for Bitcoin crypto-currency enthusiasts. Join them; it only takes a minute: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the top. Antminer S1, how to mine on multiple pools.

Thanks for your help! Then I tried shuting it down, and restarted, and it hangs up on the start, and I cant log into it anymore.

antminer s1 pool

I seem to be stuck in my tracks at this point and dont know what do to to get it going. Is there anyone that can help me? In fact Thursday took so much out of me that Saturday was pool after a full days worth of summoning the antminer to resume. Antminer am sure there pool plenty of people on here willing to help as well as myself.

What Operating System are you using?

asic - Antminer S1, how to mine on multiple pools - Bitcoin Stack Exchange

First thank you CoinHashco, for your doc, it helped me tremendously As soon as i hit apply, page cannot be founf. Hey ronminer00 You can start over with a factory reset. Im ruining linux, with a sonic wall firewall,is there anyone know how i might can just find out what address its at now so i can hit it again without doing a reset?

antminer s1 pool

Yes, im lazy, but not now least i antminer now that there is a way to do a reest. Use of this site constitutes acceptance of our User Agreement and Privacy Policy. Log in or sign up in seconds. Submit a new link. Submit a new text post. If you wish to use a wireless connection, you can view the wireless guide. The wireless guide assumes that you have first read this tutorial. Carefully remove your AntMiner S1 from the box, padding, and anti-static sleeve. What follows is a critical step for the long term health of your pool 2. This is very important.

AntMiner S1 Tutorial

You will probably need to pool the outside of both of your blades for minutes each. This thermal paste leaks up through the screw holes and from the edges of the circuit boards. My suggestion is to pool soft paper towels and no cleaning fluid. Others antminer reported pool luck with rubbing-alcohol.

You not only need to remove as much visible thermal paste as you can, but there is also an oil within the thermal paste. Both the paste and this oil can short-circuit various portions of the circuit board. The oil can be very hard to see. You should use the reflection of a light to determine where the clear oil is antminer the circuit board. Do your best to clean it up. We clean up all thermal paste that we can get to, antminer when the device heats up under use, it will tend to run down the circuit board if there is much of any left on the circuit board.

So, clean what bitmain antminer d3 купить в москве can, and check the device after 10 minutes of run time to make sure more paste did not sneak out from the screw holes. Now, placement of the S1 is important. One into each blade. There should be a 6-pin input female connector in the top center of each blade.

Похожие статьи:

  • Bitman antminer s9
  • Antminer s3
  • Nicehash antminer s4
  • Msi geforce gtx 1070 gaming x 8g 8гб

  • Рекомендуем почитать:

  • antminer buy new
  • msi rx 580 armor 8g oc mining
  • antminer s7 купить алматы
  • Gamegirlhom.ru - 2018 (c)