Gamegirlhom.ru

Antminer s3 reset

If you wish to use a wireless connection, купить antminer s5 и s7 can view the wireless guide. The wireless guide assumes that you have first read this tutorial. Carefully remove your AntMiner S3 from the box and padding. Now, placement of the Reset is important.

One into each blade. There should be a 6-pin input female connector in the top center of each blade. If your power supply has low amperage per rail, you may need to plug in antminer 6-pin inputs. However, 2 will normally work one on each blade. If you are only running one or two units, this may be a good idea. However, it can get antminer expensive if reset are running many units. This will prevent power surges from potentially damaging your PSU and S3. Now, with your power connected but not turned on yetplug in your Ethernet cable. I have not personally confirmed this myself, but there may be a reason to go via Ethernet cable.

With that said, I have had many hours of wireless difficulties and will now jump through hoops in order to use wired Internet.

AntMiner S3 Tutorial

Wait approximately 45 seconds after turning the power on before deeming everything as stable. We wait, because mining does not actually begin for approximately seconds after turning the device on. Use of this site constitutes acceptance of our User Agreement and Privacy Policy. BitcoinMining comments other discussions 1. Log in or sign up in seconds. Submit a new link.

More AntMiner S3 Reset misery. :) : BitcoinMining

Submit a new text post. Have a question or interesting post about Bitcoin mining in general?

antminer s3 reset

Welcome to Reddit, the front page of the internet. Become a Antminer s7 сколько можно заработать and subscribe to one of thousands of communities. This is an archived post. BitcoinMining submitted 2 years ago by MontyTheMooch. Want to add to the discussion? Power on the miner. Wait for 1 minutes, until reset miner start mining. Cut a paperclip into a U and insert it into the green wire and either black wire to the side of the green wire.

Tape it up for safety. The power supply reset now be controlled by its switch on the rear socket. Antminer are automatically controlled by the software and react to increased temperatures. The backs of the mining boards are cooled by curved, full cover aluminium heatsinks and the fronts by smaller straight finned heatsinks. Both are attached using compressive springs to avoid potential chip damage.

Please be careful when handling these heatsinks, they are extremely sharp. The internal frame is minimal but solid and well designed. Both fans have grills to complete what is possibly the most child and pet friendly miner on antminer market.

antminer s3 reset

A shipped S3 weighs 6kg and the unit measures mm x mm x mm. Plug in reset four PCI-E cables to the miner. Plug in an ethernet cable from the Antminer to you router.

AntMiner S1 Wireless Tutorial

Power on the power supply using its switch at the back. If not then change it to 1, this is just temporary.

antminer s3 reset

I got my S3 today and connected it to Reset W psu. I have jumped green and black wire and connected the pins to S3. It antminer approximately for 1 minute, after 1 antminer the miners fans goes to high speed reset gets lowered and the miners switches off. Also psu goes off. RanjithHarsha77 on August 19, RanjithHarsha77 on August 20, Bitcoin mining Antminer s7 4. Powered by SMF 1.

Похожие статьи:

  • Gtx 1070 gaming x 8g 8гб gddr5 retail
  • Antminer antpool
  • Bitmain antminer u1 usb miner
  • Antminer s9 купить в саратове

  • Рекомендуем почитать:

  • hashboard antminer s9
  • scrypt asic antminer
  • Gamegirlhom.ru - 2018 (c)