Gamegirlhom.ru

Config antminer s1

If you have any questions, please ask. First, you have to connect your computer and the miner directly with an Ethernet cable. Then you manually set your IP address at XXX, so you can browse the control panel.

[Setup & Troubleshoot] Bitmain AntMiner S1 GH/S miner

This is very similar to other OpenWRT based miners. Default user name and password: The LAN is useless for users, but only useful to developers. If you forget, you will not be able to login into the miner. Just Go to Hashnest. Yes, if you use less antminer, just to make sure you are not taxing all the energy into those wires. You can run config with 1 wire each, but distribute the energy to less tax config line is recommended. This is not the only way to set it up and you can tweak the setup as you please, but please do it safely!

Also the 2 small green led lights on both sides of the miner will stop flashing. Here is the video to show antminer usb btc bitcoin the minder does, when the internet connection was disrupted.

antminer

config antminer s1

When the miner regains the internet connection, the clicking noise goes away and about 30 seconds or so later, the green LEDs will start flashing again. OR It could be powered on for config 30 seconds then it shuts down. Your problem is more than likely antminer s7 купить алматы the PSU. Make sure you are not using the thin loose wire or paperclip for this If the Jumper Cable is jammed in and set correctly, it could be your power supply unit. I understand that you could be using the W or even W PSU but it may not be strong enough to do the job. Disconnect all the power cables from the 2nd Blade.

The wireless guide assumes that you have first read this antminer. Carefully remove your AntMiner S1 from the box, padding, and anti-static sleeve. What follows is a critical step for the long term health of your device 2.

config antminer s1

This is very important. You will probably need to clean the outside of both of your blades for minutes each.

antminer setup - gamegirlhom.ru

Antminer thermal paste leaks config through the antminer holes and from the edges of the circuit boards. My suggestion is to use soft paper towels and no cleaning fluid. Others have reported good luck with rubbing-alcohol. You not only need to remove as much visible thermal paste as you can, but there is also an oil config the thermal paste. Both the paste and this oil can antminer схема various portions of the circuit board.

[Setup & Tutorial] btc miner AntMiner S1 GH/s bitcoin miner asic miner for bitcoin mining

The oil can antminer very hard to see. You should use the reflection of a light to determine where the clear oil is on the circuit board. Do your best to clean it up. We clean up all thermal paste that we can get to, because when the device heats up under use, config will tend to run down the circuit board if there is much of any left on the circuit board. So, clean what you can, and check the device after 10 minutes of run time to make sure more paste did not sneak out from the screw holes. Now, placement of the S1 is important.

One into each blade. There should be a 6-pin input female bitmain antminer litecoin in the top antminer of each blade. Now, with your power connected but not turned on yetplug in your Ethernet cable. Config have not personally confirmed this myself, but there may be a reason to go via Config cable. Wait approximately 45 seconds after turning the power on before deeming everything as stable.

We wait, because mining does not actually begin for antminer seconds after turning the device on. If all is well so far, it is time to connect to your AntMiner S1 and configure it. Log into a computer on the same network as your AntMiner S1. Obtain the IP address of the S1 -- it should be on a sticker near the main fan.

Похожие статьи:

  • Gtx 1060 aero itx 6g oc майнинг
  • Msi rx 570 armor 4g oc gaming
  • What is bitcoin antminer

  • Рекомендуем почитать:

  • bitmain antminer s3 bitcoin miner
  • шумоизоляция antminer
  • Gamegirlhom.ru - 2018 (c)