Antminer s7 прошивка

And прошивка of the things it can do is run a script and take an output of that script. I installed Zabbixand got it running. It is more difficult to set it up properly, make it run reliably, and scale to thousands of devices. Once you start saving lots of data on thousand of devices, bitmain antminer s9 dash asic miner special things need to be done to the databases to optimize the installation and prevent it from bogging down. Zabbix offer support and consulting for larger and more advanced installations.

Then I needed the script. I played around with the Python application for a little while. Zabbix will let you set прошивка a antminer check using a script, but as far as I can tell it needs to be a Bash script. So I put the python script in the Zabbix externalscripts directory, and a Bash script прошивка calls the Python antminer. The output of the script is just прошивка number. I had to add a couple things. Sometimes the Antminer does not report anything back. So I have the script return a zero.

And sometimes the Antminer is not reachable over the network. Instead of having the script puke and Zabbix take the check offline, I have the script report a zero. The Bash script майнинг antminer t9 the IP address antminer uses it to call the Python script. Now прошивка everything looks good. The one box in which I need to replace the fan is showing a problem.

I rebooted one the Antminers, the trigger was activated, and the Zabbix dashboard showed the problem. When the Antminer came back online, the dashboard went green again. The graph of hashing power shows the problem also. The majority antminer the Zabbix monitoring system is working well. My current setup has some problems, though.

Once I set up the main and proxy Zabbix servers, I can monitor other locations as well. One of the things I noticed was that most of antminer customers did not have network monitoring set up and working on their systems, and the ones that did usually had it done as a service by another company, or had a network guru onsite that really understood it. Also published on Medium.

MinToRRo Bitmain Antminer Firmware S5 / S7- The Flash one!

AltcoinBitcoinMiningZenCash. Robert August 12, How much for your прошивка Rolf August 12, 8: I should do a blog post with an update antminer where I am at now with this monitoring system. Install the drivers on the PC. Most of the generic ones for Arduino work, but antminer attaching you must be sure to orient the ground pin to the one closest to the ethernet jack, sometimes labeled J1. It can physically fit antminer s9 заработок way but we want it right. The pins are symmetric 0. Lay the BBB ethernet jack to the right and look down at it.

Thats the right way. In our example the BBB pins are 1, 4, 5 active. The others are unwired. Pin 1 is J1. Its прошивка, not identical. You antminer even have little information flow arrows as guides on your board. And probably if you boot with TX and RX wrong, you just wont get a terminal. Move along, nothing else to see here. Make sure your adapter board is switched to 3. Run the USB line to the computer. The adapter board should then light up and tell you its ready as a USB serial adapter прошивка, but this isnt enough juice to power the BBB which as we remember from our last mutual annoyance is a greater 5V. Do прошивка have a serial device listed?

Try to connect from the computer via command line. Antminer may work on PC I dont know.

antminer s7 прошивка

Maybe wait if it goes to no cursor, cause your board is booting off a card. If the terminal hangs, or hangs up, check прошивка Tx and Antminer lines. They may be reversed. Switch and boot again. If you get a terminal, congratulations, you can now use your awesome linux shell skills to mole around in there and fix the issue. Sorry, I have no idea what the problem is with your board.

antminer s7 прошивка

прошивка Muck about, fix some conf files, whatever. Fix a conf file. But if you cant solve it, you now need a new board either antminer Bitmain support 0. Dead BBB board, make a new one from the store. Ok, so you tore antminer and your thing bit it. Sorry it didnt rescue. I dont know if an A5B will work, or прошивка B. I was not able to use the SD card trick on a Rev B, since mine did not boot from the boot button and SD card normally.

antminer s7 прошивка

I antminer no idea if yours will work, it might. Anyway, get a new stock BBB and try to boot it off a power supply, with the card in and the boot button down. It should flash the heartbeat and another periodic regular LED. Now get a set of BBB 23 pin headers like https: This is because your new board прошивка a big fatty and has all manner of прошивка attached, that the old one didnt, including that barrel jack we talked about. You need standoff antminer d3 купить в россии to attach it back to the unit. So, attach those headers, and you get your space. Get your Bitmain image SD card.

Go back to A to make a прошивка one if you wrote over it. Put it in the BBB. Attach antminer BBB back antminer the daughterboard. Attach power supply leads. You have to put your finger in between the mother and daughter boards.

Antminer S9 Monitoring and Alerting Application – Block Operations

That little button is right under the SD card slot. Hold it down apply power, wait for about seven seconds. I know this move sucks but its 12V. Wear latex gloves or something, make a plastic spork hook, whatever you need to do to feel safe. But you have to boot with that button depressed to get antminer ebay system to прошивка off the card. So it should work, Voila! If there was anything wrong with your BBB antminer that was the only thing bad, you прошивка now hear the antminer ant-pool config spooling up your unit in about ten seconds, using your miner to feed прошивка blocks.

Quick, go to your internet router and antminer up the network display. Working two weeks on Bitmain driver again!!! With Overkill Mode you got the best results now!!!

Antminer S9, S7, L3+ Rackmount Containment Case — BlockTree Technologies

July 28, As i can see, people had difficulties with this package So i have my things to tell now. My machines works without issues. My watts dropped more than work! Thanks and good luck for others if problems! Special thanks for Fubly! This is something and works as i need it. Powered by SMF 1. February 04,прошивка Ondart Member Offline Activity: July 09, July 10,antminer July 11, ,

Похожие статьи:

  • Antminer s9 прошивка 13th
  • Antminer l3 биткоин
  • Antminer t9 купить в москве
  • Antminer r4 описание
  • Antminer как работает
  • Bitcoin шахтер antminer s9 купить

  • Рекомендуем почитать:

  • antminer s10 когда выйдет
  • antminer u2 отзывы
  • msi gtx 1060 armor 6g ocv1 комплектация
  • - 2018 (c)