I really like your comprehensive check list you made that depict which feature the antminer has or not. Anyhow, my biggest worry about getting an S7 is the noise. The new S7 is with different controller all data cable connectors is in one way. Also, the housing is different from antminer the top. The older housing is from top smooth, like an your pictures. Great guide as always. What reset do you use to take those?
I always am amazed by your photo work. Hero Member Offline Activity: Tupsu on September 27, Finksy on October 01, Is it wise to advise others to go against something they have made explicitly clear against doing antminer etherium whatever reason? Will I do it myself? Of course not The splitters that dogie linked to are the right way to go, for how much they cost they give you peace of mind in regards antminer avito warranty. Reset are two reasons I can think of that you might "need" 3 connectors rather than 2.
First is the current rating of the contacts in the connector. In this case using a splitter will protect the Miner connectors however it will not protect the connector that is plugged into the splitter. So good antminer купить в самаре the Miner Warranty point of view but of no value from an overall reliability point of view. I received an e mail saying repair or replacement of my broken hash board was complete and I would have my Reset back in full working condition in 3 days.
I was very impressed by support and the warranty process at this point even though I had spent so much time on antminer and paid for shipping. Received mu miner yesterday and it is in the same exact condition. Why would you put me through all this work and have me pay shipping and just send back the miner to me in the exact same condition? I have been so polite. I have followed all your repair instructions and I am still under reset. Why are you putting me through so much grief? As you can see above I shipped my S9 to the California repair facility as it is still under warranty. I was told repair or replacement of the broken hash board was complete. Look at the screen shot of my miner, still broken, the same, actually worse as now the Chip1 temps are missing as well.
It was obvious the 1 broken hash board was the issue yet you made me pay and ship the whole miner to you instead of simply sending me a replacement hash board. And then after I pay shipping antminer send it in for repair as instructed you reassured me it was fixed.
Why did you just send me back the miner with the same broken hash board? Yeah bro I want to but I need to know they will honor the day warranty first. I would have already ordered more D3 and the new S9 that is releasing but I need my original S9 under warranty fixed first bro.
Yeah looks like my mining project is over.
Now I gotta call up all the friends I referred and give them a heads up that reset warranty is fake. Very sad and disappointed with bitmain. A piece of heat sink is not glued on msi gtx 1070 armor 8g oc отзывы dropped off. Remove the hash board that exceeds 80 degrees to repair.
The hash rate is in the normal range, but there is no temp shown on the Miner status The hash board is easily get burnt if there is no temp shown on when the real temp is high Reason: The chip is damaged, which resulted in the loss of hash rate on one hash board. The chips are damaged, which lead to the entire hash board running abnormal. Remove the hash board to repair. It was caused by chain scission of chips Solution: The firmware of miner is lost. Power off the miner and reset it to see if that worked 8. The firmware of miner cannot be detected. Antminer of the fans was not detected.
Only when two fans are detected can miner work well. Switch the fan and IO board in turn to reset out which one is defective. One of the computers in the network has been captured by viruses. Kill the virus or format it. Green light does not shine. Reset the power for several antminer. There is no use replacing the PSU.
Power on the power supply using its switch at the back. You can assume it is already on if you have a typical router. Using a browser, navigate to your router and find the IP it reset assigned the S7 and navigate to that IP. Login using antminer as both the username and password. Enter your pool information in the below format.
Navigate to the page "Miner Status" to check mining has started. Under ASIC status, one row is almost all "x"es? How do I reset settings to default? How do I change the login password? What is the SSH antminer What do the LEDs on the front reset
Will the miner antminer beep? Short of having really dirty power with lots of over voltage, it sounds to me like the power supply itself may well be the culprit. Are you sure you have enough power at the wall outlet? If you have multiple large power supplies running on the same circuit, even if it reset multiple outlets, then you can easily overload the circuit with unpredictable results.
Your current power supply on the unit that is acting up could easily be very sensitive to an under voltage or circuit overload. Use my Accumining link for 5 free Ghs for 1 month. My feeling is that the fan is kicking high due to undervolt causing amperage spikes and thus creating heat at an exponential rate.
TCB47 also brings up a good point. At the very least make sure that there is nothing else on the circuit that you are using for that particular miner. To go up to 20 amps reset need 12 gauge minimum by NEC code. The antminer bit of info we have from your video and what I think antminer actually antminer l3 504mh с reset me very concerned that you are running a risk of electrical fire. I would take that "delay" our of the equation and go from there. Hit me with a PM if you want to take me up on the wattage monitor.
Loading Categories Disabled Categories are greyed out This topic will be moved to the category.